Welcome Guest ( Log In)

 
Reply to this topicStart new topicStart Poll

Outline · [ Standard ] · Linear+

> Size box and part shifted out of wack

LDRUGGE
post Aug 11 2017, 12:59 AM
Post #1


New Member


Group: Community Members
Posts: 3
Joined: 10-August 17
Member No.: 73,104



I'm quite new to IronCad and I have run into some problems which I canít solve by myself. And my more experienced collagues canít help me either.

I have created a hollow square tube like in the picture below. During that work I have done some kind of mistake and decoupled the size box from the part.

Sp when I pull the red handles I only change the size of the size box and the part size is not changed. The only direction I can change the part is the width, length and height are not possible.
The size box is also moved from the center of the part as shown in picture 2.

Why has this happened?
Is it possible to connect the sizebox to the part again?
How do I center the size box in the part?

This post has been edited by LDRUGGE: Aug 11 2017, 02:39 AM

Attached thumbnail(s)
Attached Image Attached Image
User is offlineProfile CardPM
Go to the top of the page
+Quote Post
Cary OConnor
post Aug 11 2017, 08:06 AM
Post #2


TriBall
********

Group: IronCAD Employees
Posts: 6,532
Joined: 23-August 04
Member No.: 17



Can you attach the .ICS file?

Thanks
Cary
User is offlineProfile CardPM
Go to the top of the page
+Quote Post
LDRUGGE
post Aug 11 2017, 09:13 AM
Post #3


New Member


Group: Community Members
Posts: 3
Joined: 10-August 17
Member No.: 73,104



Here is the ics.

fileAttached File  RHS_40x40x4x1000.ics ( 96.5k ) Number of downloads: 16
User is offlineProfile CardPM
Go to the top of the page
+Quote Post
Cary OConnor
post Aug 11 2017, 09:40 AM
Post #4


TriBall
********

Group: IronCAD Employees
Posts: 6,532
Joined: 23-August 04
Member No.: 17



Open your file. Select the Part. Go to the Tools Ribbon Bar and select "Reset Sizebox". This will reset it and reset all the feature handles as well. Right-click on the Part and go to Part Properties. Select Sizebox and change all the Resizing Behaviors to "From Opposite Handle".

This should reset you back to the original behavior. Note: Pulling on the handles in this case will essentially scale. This is fine in the Height direction but not in the L/W. You will need to constrain some geometry to get it to work properly in those directions.

Cary
User is offlineProfile CardPM
Go to the top of the page
+Quote Post
LDRUGGE
post Aug 14 2017, 01:27 AM
Post #5


New Member


Group: Community Members
Posts: 3
Joined: 10-August 17
Member No.: 73,104



QUOTE(Cary OConnor @ Aug 11 2017, 10:40 AM)
Open your file. Select the Part. Go to the Tools Ribbon Bar and select "Reset Sizebox". This will reset it and reset all the feature handles as well. Right-click on the Part and go to Part Properties. Select Sizebox and change all the Resizing Behaviors to "From Opposite Handle".

This should reset you back to the original behavior. Note: Pulling on the handles in this case will essentially scale. This is fine in the Height direction but not in the L/W. You will need to constrain some geometry to get it to work properly in those directions.

Cary
*




Works like a charm..thank you very much
User is offlineProfile CardPM
Go to the top of the page
+Quote Post

Reply to this topicTopic OptionsStart new topic
1 User(s) are reading this topic (1 Guests and 0 Anonymous Users)
0 Members:
 

All content copyright IronCAD 2000-2008 Low-Bandwidth View Time is now: 22nd November 2017 - 07:50 AM